fbpx

Cat 908 Compact Wheel Loader

Cat® wheel loaders set the standard for productivity, fuel efficiency and operator comfort. The Cat 908 Compact Wheel Loader has a high torque C2.8 engine that works in conjunction with an intelligent hystat power train to deliver exceptional fuel efficiency. “Shift on the go” locking differentials and hydrostatic transmission provide smooth and powerful operation while increasing the efficiency of machine cycles.

Maximum Gross Power 55.7 kW
Engine Model Cat C2.8*
Maximum Gross Power - Rated Engine Speed 2400 r/min
Rated Net Power - Rated Engine Speed 2400 r/min
Maximum Gross Power - ISO 14396 (metric) 75.3 mhp
Rated Net Power - SAE J1349 54.2 kW
Maximum Engine Speed 2550 rpm
Rated Net Power - ISO 9249 53.8 kW
Maximum Gross Torque - SAE J1995 300 N·m
Maximum Gross Power - SAE J1995 55.7 kW
Maximum Gross Torque - ISO 14396 300 N·m
Maximum Net Torque - SAE J1349 296 N·m
Maximum Net Torque - ISO 9249 295 N·m
Rated Net Power - 2,400 rpm - ISO 9249 (metric) 73.1 mhp
Bore 90 mm
Stroke 110 mm
Displacement 2.8 l
Maximum Gross Power - ISO 14396 55.4 kW
Note *Meets U.S. EPA Tier 4 Final and EU Stage V emission standards.
Note (1) Maximum gross and net torque measured at 1,600 rpm.
Note (2) Net power ratings are tested at the reference conditions for the specified standard.
Note (3) Net power advertised is the power available at the flywheel.

Operating Weight 6632 kg

Bucket Capacities 0.75-1.55 m³ (1.0-2.0 yd³)
Multi-Purpose 0.75-1.1 m³ (1.0-1.4 yd³)
Note All capacities are applicable for each model. Bucket selection must be made with an understanding of the material density and application to ensure machine stability is maintained within the tipping loads stated per model and configuration.
Note (1) Bucket capacities stated include BOCE, in line with ISO 7546.
Bucket Capacities - General Purpose 0.80-1.35 m³ (1.0-1.7 yd³)
Bucket Capacities - Light Material 1.25-1.55 m³ (1.6-2.0 yd³)

Height: Ground to Cab** 2670 mm
Height: Ground to Beacon** 2853 mm
Height: Ground Axle Center** 519 mm
Height: Ground Clearance** 320 mm
Length: Overall* 6163 mm
Length: Rear Axle to Bumper 1391 mm
Length: Hitch to Front Axle 1085 mm
Length: Wheel Base 2170 mm
Clearance: Bucket at 45° * 3294 mm
Clearance: Load over Height** 4238 mm
Clearance: Level Bucket** 3682 mm
Height: Bucket Pin** 3889 mm
Height: Overall** 4789 mm
Reach: Bucket at 45° * 1042 mm
Carry Height: Bucket Pin 508 mm
Dig Depth** 72 mm
Width: Bucket 2080 mm
Width: Tread Center 1570 mm
Turning Radius: Over Bucket 4869 mm
Width: Over Tires 1990 mm
Turning Radius: Outside of Tires 4087 mm
Turning Radius: Inside of Tires 2033 mm
Rack Angle at Full Lift 70°
Dump Angle at Full Lift 40°
Rack Angle at Carry 47°
Departure Angle - Degrees 30°
Articulation Angle - Degrees 39°
Operating Weight: Bucket ^ 6762 kg
Tipping Load - Straight - ISO 14397-1 † 4113 kg
Tipping Load - Full Turn - ISO 14397-1 † 3446 kg
Operating Weight: Carriage and Tines ^^ 6771 kg
Tipping Load - Straight † 3194 kg
80% of Tip: Firm and Level EN474-3 †† 2152 kg
Note (1) *Vary with bucket
Note (2) **Vary with tire
Note (3) ^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL), 1.15 m3 (1.5 yd3) general purpose bucket.
Note (4) ^^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL), class III carriage, 1220 mm (4 ft) tines (500 mm [20 in] load center).
Note (5) †Full compliance to ISO 14397-1 (2007) Sections 1 thru 6 (fork 500 mm [20 in] load center), which requires 2% verification between calculation and testing.
Note (6) ††Full compliance to EN474-3 and SAE J1197.
Note (7) #HPL-A weight, tipping and rated loads are within 1% of the HPL-V.
Note (8) Dimensions listed are for a machine configured with standard cab, heater, 20 km/h (12 mph), standard guarding, 80 kg (176 lb) operator, full fluids, SPT9 405/70 R20 tires and 1.15 m3 (1.5 yd3) general purpose bucket with bolt-on cutting edge or a class III fork carriage and tines, (tire supplier variability can impact dimensions by 2%).

Height: Ground to Cab** 2670 mm
Height: Ground to Beacon** 2853 mm
Height: Ground Axle Center** 519 mm
Height: Ground Clearance** 320 mm
Length: Overall* 6319 mm
Length: Rear Axle to Bumper 1391 mm
Length: Hitch to Front Axle 1085 mm
Length: Wheel Base 2170 mm
Clearance: Bucket at 45° * 3131 mm
Clearance: Load over Height** 4238 mm
Clearance: Level Bucket** 3675 mm
Height: Bucket Pin** 3889 mm
Height: Overall** 4880 mm
Reach: Bucket at 45° * 1098 mm
Carry Height: Bucket Pin 529 mm
Dig Depth** 80 mm
Width: Bucket 2080 mm
Width: Tread Center 1570 mm
Turning Radius: Over Bucket 4912 mm
Width: Over Tires 1990 mm
Turning Radius: Outside of Tires 4087 mm
Turning Radius: Inside of Tires 2033 mm
Rack Angle at Full Lift 66°
Dump Angle at Full Lift 33°
Rack Angle at Carry 41°
Departure Angle - Degrees 30°
Articulation Angle - Degrees 39°
Operating Weight: Bucket ^ 6862 kg
Tipping Load - Straight - ISO 14397-1 † 3749 kg
Tipping Load - Full Turn - ISO 14397-1 † 3126 kg
Operating Weight: Carriage and Tines ^^ 6834 kg
Tipping Load - Straight † 2923 kg
80% of Tip: Firm and Level EN474-3 †† 1982 kg
Note (1) *Vary with bucket
Note (2) **Vary with tire
Note (3) ^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL), 1.15 m3 (1.5 yd3) general purpose bucket.
Note (4) ^^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL), class III carriage, 1220 mm (4 ft) tines (500 mm [20 in] load center).
Note (5) †Full compliance to ISO 14397-1 (2007) Sections 1 thru 6 (fork 500 mm [20 in] load center), which requires 2% verification between calculation and testing.
Note (6) ††Full compliance to EN474-3 and SAE J1197.
Note (7) #HPL-A weight, tipping and rated loads are within 1% of the HPL-V.
Note (8) Dimensions listed are for a machine configured with standard cab, heater, 20 km/h (12 mph), standard guarding, 80 kg (176 lb) operator, full fluids, SPT9 405/70 R20 tires and 1.15 m3 (1.5 yd3) general purpose bucket with bolt-on cutting edge or a class III fork carriage and tines, (tire supplier variability can impact dimensions by 2%).

Height: Ground to Cab** 2670 mm
Height: Ground to Beacon** 2853 mm
Height: Ground Axle Center** 519 mm
Height: Ground Clearance** 320 mm
Length: Overall* 5549 mm
Length: Rear Axle to Bumper 1391 mm
Length: Hitch to Front Axle 1085 mm
Length: Wheel Base 2170 mm
Clearance: Bucket at 45° * 2615 mm
Clearance: Load over Height** 2957 mm
Clearance: Level Bucket** 3197 mm
Height: Bucket Pin** 3404 mm
Height: Overall** 4304 mm
Reach: Bucket at 45° * 770 mm
Carry Height: Bucket Pin 353 mm
Dig Depth** 109 mm
Width: Bucket 2080 mm
Width: Tread Center 1570 mm
Turning Radius: Over Bucket 4570 mm
Width: Over Tires 1990 mm
Turning Radius: Outside of Tires 4087 mm
Turning Radius: Inside of Tires 2033 mm
Rack Angle at Full Lift 53°
Dump Angle at Full Lift 45°
Rack Angle at Carry 51°
Departure Angle - Degrees 30°
Articulation Angle - Degrees 39°
Operating Weight: Bucket ^ 6632 kg
Tipping Load - Straight - ISO 14397-1 † 4812 kg
Tipping Load - Full Turn - ISO 14397-1 † 4060 kg
Operating Weight: Carriage and Tines ^^ 6467 kg
Tipping Load - Straight † 3920 kg
80% of Tip: Firm and Level EN474-3 †† 2638 kg
Note (1) *Vary with bucket
Note (2) **Vary with tire
Note (3) ^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL), 1.15 m3 (1.5 yd3) general purpose bucket.
Note (4) ^^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL), class III carriage, 1220 mm (4 ft) tines (500 mm [20 in] load center).
Note (5) †Full compliance to ISO 14397-1 (2007) Sections 1 thru 6 (fork 500 mm [20 in] load center), which requires 2% verification between calculation and testing.
Note (6) ††Full compliance to EN474-3 and SAE J1197.
Note (7) #HPL-A weight, tipping and rated loads are within 1% of the HPL-V.
Note (8) Dimensions listed are for a machine configured with standard cab, heater, 20 km/h (12 mph), standard guarding, 80 kg (176 lb) operator, full fluids, SPT9 405/70 R20 tires and 1.15 m3 (1.5 yd3) general purpose bucket with bolt-on cutting edge or a class III fork carriage and tines, (tire supplier variability can impact dimensions by 2%).

Main Relief - 1st Auxiliary (3rd slice) 23500 kPa
Main Relief - 1st Auxiliary (3rd slice) - Standard Flow 90 l/min
Main Relief - 1st Auxiliary (3rd slice) - High Flow 125 l/min
Main Relief - 2nd Auxiliary (4th slice) 23500 kPa
Main Relief - 2nd Auxiliary (4th slice) - Flow 45 l/min
Hydraulic Cycle Time - Lift 5.8 s
Hydraulic Cycle Time - Dump 1.8 s
Hydraulic Cycle Time - Float Down 3.6 s
Hydraulic Cycle Time - Rackback 2.5 s
Note *Adjustable from 20% to 100% of maximum flow through display.

Tire Size - Standard *405/70 R20 SPT9
Tire Size - Optional 405/70 R20 Powerloads
Tire Size - Optional (1) 400/70 R20 XMCL/Bibload
Tire Size - Optional (2) 360/80 R20 TRI 2
Tire Size - Optional (3) 40X14-20 TL, SM/TR
Note *This tire has been used for all dimension, stability and performance data.
Note (1) Other tire choices are available. Contact your Cat dealer for details.
Note (2) In certain applications, the loader’s productive capabilities may exceed the tire’s tonnes-km/h (ton-mph) capabilities.
Note (3) Caterpillar recommends that you consult a tire supplier to evaluate all conditions before selecting a tire model.

Forward and Reverse - Speed Range Creep# 10 km/h
Forward and Reverse - Speed Range 2** - High Speed 18 km/h
Forward and Reverse - Speed Range 2** - Standard 19 km/h
Forward and Reverse - Speed Range 3*** 40 km/h
Note (1) *Creep function not available in this gear or above.
Note (2) **Max speed dependent on model and configuration (standard vs. high speed transmission).
Note (3) ***Reverse is 30 km/h (19 mph).
Forward and Reverse - Speed Range 1* 10 km/h
Note #Factory default shown, can be adjusted to any speed up to 19 km/h (12 mph).

Height: Ground to Beacon** 2853 mm
Height: Ground Axle Center** 519 mm
Length: Rear Axle to Bumper 1391 mm
Length: Hitch to Front Axle 1085 mm
Clearance: Load over Height** 2957 mm
Height: Overall** 4395 mm
Carry Height: Bucket Pin 374 mm
Turning Radius: Outside of Tires 4087 mm
Rack Angle at Full Lift 49°
Rack Angle at Carry 53°
Departure Angle - Degrees 30°
Articulation Angle - Degrees 39°
Operating Weight: Bucket ^ 6718 kg
Tipping Load – Straight – ISO 14397-1 † 4347 kg
Tipping Load – Full Turn – ISO 14397-1 † 3623 kg
Operating Weight: Carriage and Tines ^^ 6530 kg
Tipping Load - Straight † 3649 kg
80% of Tip: Firm and Level EN474-3 †† 2468 kg
Note (1) *Vary with bucket
Note (2) **Vary with tire
Note (3) ^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL), 1.15 m3 (1.5 yd3) general purpose bucket.
Note (4) ^^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL), class III carriage, 1220 mm (4 ft) tines (500 mm [20 in] load center).
Note (5) †Full compliance to ISO 14397-1 (2007) Sections 1 thru 6 (fork 500 mm [20 in] load center), which requires 2% verification between calculation and testing.
Note (6) ††Full compliance to EN474-3 and SAE J1197.
Note (7) #HPL-A weight, tipping and rated loads are within 1% of the HPL-V.
Note (8) Dimensions listed are for a machine configured with standard cab, heater, 20 km/h (12 mph), standard guarding, 80 kg (176 lb) operator, full fluids, SPT9 405/70 R20 tires and 1.15 m3 (1.5 yd3) general purpose bucket with bolt-on cutting edge or a class III fork carriage and tines, (tire supplier variability can impact dimensions by 2%).
Height - Ground to Cab 2670 mm
Height - Ground Clearance 320 mm
Length - Wheel Base 2170 mm
Length - Overall with Bucket 5707 mm
Reach - Bucket at 45° 872 mm
Dig Depth 117 mm
Clearance - Bucket at 45° 2502 mm
Clearance - Level Bucket 3189 mm
Height - Bucket Pin 3404 mm
Turning Radius - Over Bucket 4613 mm
Turning Radius - Inside Tire 2033 mm
Width - Bucket 2080 mm
Width - Tread Center 1570 mm
Width - Over Tires 1990 mm
Dump Angle at Full Lift 45°

Note Oscillation of ±11 degrees via hitch between front and rear frames.
Front Fixed Locking Differential (standard)
Rear Fixed Locking Differential (standard)

Steering Cycle Times – (full left to full right) – at High Idle 3 s
Maximum Flow - Steering Pump 46.7 l/min
Maximum Working Pressure - Steering Pump 23000 kPa
Number of Steering Wheel Turns - Full Left to Full Right or Full Right to Full Left 3.25 turns or 4.00 turns
Steering Articulation Angle - Each Direction 39 °

Fuel Tank 90 l
Cooling System 12 l
Transmission 2.4 l
Note No Diesel Exhaust Fluid (DEF) fluid needed on this size engine.
Axles - Front Center Differential 8.8 l
Axles - Rear Center Differential 8.8 l
Engine Crankcase 8.8 l
Hydraulic System - Including Tank 70.5 l
Hydraulic Tank 44.6 l

ROPS ISO 3471:2008
FOPS ISO 3449:2005 Level II
Note (1) Canopy and cab, Rollover Protective Structures (ROPS) are available worldwide. Canopy not available in EU.
Note (2) The declared dynamic operator sound pressure levels per ISO 6396:2008*, when properly installed and maintained, is 71 dB(A).
Note (3) *Measurements were conducted with the cab doors and windows closed.
Note (4) The labelled sound power level for the CE marked configurations when measured according to the test procedure and conditions specified in 2000/14/EC is 101 dB(A). 99 dB(A) Low Sound – Option available.

Recyclability 93%

Ask Quotation

Usados

SOLUTIONS THAT SIMPLIFY

(Free) 800 206 707

STET
Websites